Delta HMI

Thank you for purchasing DOPB07S411 Delta HMI. This instruction sheet will be helpful in the installation, wiring and inspection of Delta HMI. Before using the product, please read this instruction sheet to ensure correct use. You should thoroughly understand all safety precautions before proceeding with the installation, wiring and operation. Place this instruction sheet in a safe location for future reference. Please observe the following precautions: 

• Install the product in a clean and dry location free from corrosive and inflammable gases or liquids.
• Ensure that all wiring instructions and recommendations are followed.
• Ensure that HMI is correctly connected to a ground. The grounding method must comply with the electrical standard of the country (Please refer to NFPA 70: National Electrical Code, 2005 Ed.).
• Do not disassemble HMI, modify or remove wiring when power is applied to HMI.
• Do not touch the power supply during operation. Otherwise, it may cause electric shock.

• Please read this instruction carefully before use.
• Switch off the power before wiring.
• The display panel of TP02 series is waterproof. But please prevent grease, corrosive liquids and sharp objects from contacting the TP02 series.
• The TP02 series require 24VDC input power. DO NOT connect input AC power supply to any of the RS-485 communication port; otherwise serious damage may occur. Check all the wiring again before switching on the power.
• Do not touch any terminal when the power is switched on. Do not touch any internal circuit in 1 minute after the power is switched off.
• Make sure the groud terminal is correctly grounded in order to prevent electromagnetic interference.
• Please use the fixed support accessory which is packed together with the product provided by Delta. DO NOT tighten the screws out of the normal torque specifications; otherwise serious damage may occur.

Introduction 1.1 Model Explanation

• Thank you for choosing Delta TP Series. TP02G-AS1 has the features of high resolution 160×32 dots. It provides multilingual display and two built-in communication ports, one is for RS-232 and the other is for RS-485. RS-232 and RS-485 can be used simultaneously. Besides, it also supports communication and alarm LED indicators. The user can purchase program copy card (optional) to copy settings and programs quickly and save download time.

(1) General precautions Thank you for purchasing this product. This instruction sheet provides information about the DOP-100 series HMI. Before using this product, please read through this instruction sheet carefully to ensure the correct use of the product. Please keep this sheet handy for quick reference whenever needed. Before finishing reading this sheet, please follow the instructions below:

• Install the product in an indoor location, which is free of vapor, corrosive and inflammable gas and liquids. 
• Please refer to the wiring diagram when connecting the wires.
• Ensure your HMI is correctly grounded. The grounding method must comply with the national electrical standard (please refer to NFPA 70: National Electrical Code, 2005 Ed.). Do not disassemble the HMI or change the wiring when power is on.
• Do not touch the power supply when power is on, or it may cause electric shock.
• When the HMI displays a low power notification and requires a battery change, please contact your local distributor or Delta Customer Service Center for the replacement. Do not change the batteries by yourself.
• This product can be used with other industrial automation equipment. Please read through this sheet carefully and install the product according to the instructions to avoid danger.
• Cleaning method: please use a dry cloth to clean the product.
• This product must be used at an altitude below 2,000 m.
• If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired. 

Established as a Proprietor firm in the year 1995, we “Maruti Electromac” are a leading Manufacturer And Trader of a wide range of Control Panel, VFD Panel and automatic control panel and PLC control panel . Situated in Ahmedabad (Gujarat, India), we have constructed a wide and well functional infrastructural unit that plays an important role in the growth of our company. We offer these products at reasonable rates and deliver these within the promised time-frame. Under the headship of “Mr. Pareshbhai Natvarlal Patel” (CEO), we have gained a huge clientele across the nation.

Established as a Proprietor firm in the year 1995, we “Maruti Electromac” are a leading Manufacturer And Trader of a wide range of Control Panel, VFD Panel and automatic control panel and PLC control panel . Situated in Ahmedabad (Gujarat, India), we have constructed a wide and well functional infrastructural unit that plays an important role in the growth of our company. We offer these products at reasonable rates and deliver these within the promised time-frame. Under the headship of “Mr. Pareshbhai Natvarlal Patel” (CEO), we have gained a huge clientele across the nation.

Established as a Proprietor firm in the year 1995, we “Maruti Electromac” are a leading Manufacturer And Trader of a wide range of Control Panel, VFD Panel and automatic control panel and PLC control panel . Situated in Ahmedabad (Gujarat, India), we have constructed a wide and well functional infrastructural unit that plays an important role in the growth of our company. We offer these products at reasonable rates and deliver these within the promised time-frame. Under the headship of “Mr. Pareshbhai Natvarlal Patel” (CEO), we have gained a huge clientele across the nation.